Allen-Bradley 2-D Manual de usuario Pagina 96
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming
5-27
Frequency Set Group (continued)
[
D
e
c
e
l
T
im
e
2
]
Parameter # 31 Factory Default 5.0 Sec
[
D
e
c
e
l
T
im
e
2
]
Parameter Type Read & Write Minimum 0.0 Sec
This value determines the time it will take the drive to ramp
from [Maximum Freq] to 0 Hz. The rate is linear unless
[S Curve] is ‘‘Enabled” or [Stop Select] is set to
‘‘S-Curve.” It applies to any decrease in command
frequency unless [Decel Time 1] is selected. Refer to
charts on Pages 5-29 and 5-30.
Units 0.1 Second Maximum 3600.0 Sec
[
P
re
s
et
F
re
q 1
-
7
]
Parameter # See Table Factory Default See Table Parameter No. Default
[
P
re
s
et
F
re
q 1
-
7
]
Parameter Type Read & Write Minimum 0.0 Hz
[Preset Freq 1] 27 10.0 Hz
These values set the frequencies that the drive will output
w e ee e . e er ar a e 5-29 a 5-30.
Units 0.1 Hz Maximum 400.0 Hz
[Preset Freq 2] 28 20.0 Hz
Th
e
s
e
v
a
lu
e
s s
e
t th
e
f
req
u
e
nc
ie
s th
a
t th
e
d
ri
v
e
wi
ll output
when selected. Refer to charts on Pages 5-29 and 5-30.
Uni
t
s
0.1
Hz
Max
imum
400.0
Hz
[Preset Freq 3] 29 30.0 Hz
[Preset Freq 4] 73 40.0 Hz
[Preset Freq 5] 74 50.0 Hz
[Preset Freq 6] 75 60.0 Hz
[Preset Freq 7] 76 0.0 Hz
[
Ski
p
F
re
q 1
-
3
]
Parameter # 32-34 Factory Default 400 Hz
[
Ski
p
F
re
q 1
-
3
]
Parameter Type Read & Write Minimum 0 Hz
These values, in conjunction with [Skip Freq Band],
create a range of frequencies at which the drive will not
operate continuously.
Units 1 Hz Maximum 400 Hz
Programming the drive for Frequency Source and Accel/Decel Control
Use Table 5.A through Table 5.C to determine which frequency source and Accel/Decel Time are suitable to your application.
Switch or contact inputs at terminal TB2 are used to select functionality based on how you program parameters (26), (72), and (21).
- 1305 Adjustable 1
- Frequency AC Drive 1
- (Series C) 1
- PLEASE READ! 2
- IMPORTANT USER INFORMATION 2
- Summary of Changes 3
- SUMMARY OF DRIVE ENHANCEMENTS 4
- Table of Contents 7
- Appendix D – CE Conformity 8
- GENERAL PRECAUTIONS 10
- NAMEPLATE LOCATION 12
- 1305-BA03A-HAP SER C 12
- FIRMWARE COMPATIBILITY 12
- 1305 – A02 AA 13
- Information and Precautions 14
- Installation/Wiring 15
- TERMINAL BLOCK ACCESS 17
- INPUT DEVICES 19
- INPUT POWER CONDITIONING 20
- INPUT FUSING 20
- RFI FILTERING 22
- POWER WIRING 25
- P-P insulation design 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- User Side 34
- OUTPUT DEVICES 36
- CABLE TERMINATION 36
- ADAPTERS 37
- HIM DESCRIPTION 39
- HIM OPERATION 39
- Human Interface Module 40
- OFF Steady ON 41
- Steady ON OFF 41
- Flashing Steady ON 41
- Steady ON Flashing 41
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- OPERATOR LEVEL 44
- MODE LEVEL 44
- GROUP LEVEL 44
- PARAMETER LEVEL 44
- PROGRAM AND DISPLAY MODES 45
- Accel Time 46
- 99.9 Secs 46
- Choose Group 46
- Adapter 4 47
- X1111111 47
- PROCESS MODE 48
- Choose Mode 49
- Process Text 1 49
- EEPROM MODE 50
- EEPROM MODE (continued) 51
- CONTROL STATUS MODE 54
- PASSWORD MODE 56
- PASSWORD MODE (continued) 57
- Start-Up 60
- DESCRIPTION 61
- HIM DISPLAY 61
- Bul. 1305 Drive 62
- Connection Fail 62
- Open Enable Signal 65
- Restore Enable Signal 65
- Remove ALL Power 67
- Reconnect Motor 67
- Slowly Increase Speed 69
- PROGRAMMING EXAMPLE 73
- Metering Group (continued) 75
- 5-2 & 5-3 77
- Setup Group (continued) 78
- Figure 5.10 Start/Run Boost 88
- Figure 5.12 Analog Invert 90
- Two times 97
- [Skip Freq Band] 97
- Programming 100
- (continued) 100
- Figure 5.16 S-Curve 102
- Figure 5.17 S-Curve Time 103
- [( )])( )( 104
- Faults Group (continued) 109
- Diagnostics Group (continued) 112
- Masks Group (continued) 117
- Owners Group (continued) 120
- CHAPTER OBJECTIVES 126
- FAULT INFORMATION 126
- (continued) 129
- Appendix 138
- Table A.1 Specifications 139
- Serial Communications 144
- LOGIC CONTROL DATA 145
- DRIVE STATUS DATA 145
- SCALE FACTOR CONVERSION 145
- 25% of DRV 149
- 20% of DRC 149
- Drive Accessories 160
- ➀ Input reactor only 161
- CE Conformity 162
- ELECTRICAL CONFIGURATION 164
- GROUNDING 164
- CUT ALONG DOTTED LINE 170
Relacionado con productos y manuales para Lectores De Códigos De Barras Allen-Bradley 2-D
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales