Allen-Bradley Rockwell Automation 1734-AENT Manual de usuario Pagina 83
- Pagina / 158
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
67 Publication 1734-UM011D-EN-P - May 2011
Appendix
A
Adapter Web Pages
What This Appendix
Contains
Read this appendix for information about the adapter Web page diagnostics
that offer extensive internal and network diagnostics.
Work with the Home Page
Use the adapter diagnostics Home page to access other adapter diagnostics
Web pages and see the following information.
•Host Name
• Module Description
• Module Location
• IP Address
• Ethernet Address (MAC)
•DHCP Enabled
• Product Revision
• Serial Number
• Status
• Auto Negotiate
• Media Speed
•Half or Full Duplex
To display and work with the adapter diagnostics Home page, follow these
procedures.
Topic Page
Work with the Home Page 67
Work with the Diagnostics Pages 69
Work with the Configuration Pages 76
Work with the Browse Chassis Page 80
IMPORTANT
Make sure that your PC Internet LAN setting and your
TCP/IP settings are configured to access the subnet on
which your adapter communicates.
- Catalog Number 1734-AENT 1
- User Manual 1
- Important User Information 2
- ATTENTION 3
- How to Use This Manual 4
- System Components 5
- Where to Find More 6
- Information 6
- Terminology 7
- Preface ix 9
- Table of Contents 11
- xiii 13
- Summary of Changes 15
- About the Adapter 17
- Adapter Replacement 18
- About the Adapter 3 19
- Adapter Features 20
- Hardware/Software 21
- Compatibility 21
- What the Adapter Does 21
- Use of the Common 21
- Industrial Protocol (CIP) 21
- Understand the 22
- Producer/Consumer Model 22
- Specify the Requested 22
- Packet Interval (RPI) 22
- Support of Rack-optimized 23
- Before You Begin 24
- Install the Adapter 25
- Mount the Adapter on a DIN 26
- Rail Before Installing 26
- Mount or Replace 27
- Existing System 27
- Wire Your Adapter 28
- Mounting Dimensions 29
- 14 Install the Adapter 30
- What This Chapter Contains 31
- Configuration 32
- Requirements 32
- IP Address 33
- Gateway Address 33
- Subnet Mask 34
- Set the Network Address 35
- Use the Rockwell 36
- BootP/DHCP Utility 36
- Save the Relation List 38
- Use DHCP Software to 39
- Configure Your Adapter 39
- Set Up the Hardware 41
- Create the Example 42
- Application 42
- Configure the I/O 43
- Name Local_ENB 46
- IP Address 10.88.70.4 46
- Revision 3.1 46
- Add the Relay Output Module 49
- The New Module dialog opens 50
- Name POINT_Relay_Output 51
- Add the Digital Output Module 52
- Name POINT_Digital_Output 53
- Edit the Controller Tags 54
- Create the Ladder Program 55
- Download the Program to 55
- Verify the Module Chassis 57
- 8. Click OK to continue 58
- Configure the Adapter with 59
- Fixed IP Address 59
- Recover From an 60
- Overloaded Adapter 60
- Software 61
- Configure the I/O Modules 64
- Revision 1.1 66
- Connection 69
- 5. Choose Connection 70
- Verify the Module 75
- Chassis Size 75
- 3. Select Properties 76
- 4. Click the Connection tab 76
- → Save to save the project 77
- Access Module Data 78
- LED Status Indicators 79
- Adapter Web Pages 83
- Work with the Diagnostics 85
- 70 Adapter Web Pages 86
- Use the Network Settings Page 87
- 72 Adapter Web Pages 88
- Adapter Web Pages 73 89
- Use the I/O Connections Page 90
- Adapter Web Pages 75 91
- Work with the 92
- Configuration Pages 92
- Use the Identity Page 93
- 78 Adapter Web Pages 94
- Adapter Web Pages 79 95
- Work with the Browse 96
- Chassis Page 96
- •Module Revision 99
- • Serial Number 99
- • Status 99
- 84 Adapter Web Pages 100
- Communication Driver 101
- Configure the AB_ETH/IP 102
- Controller Tag Reference 105
- Valid Number Ranges for 106
- RSLogix 5000 Data Types 106
- Digital 2 POINT Input 107
- Digital 4 POINT Input 108
- Digital 2 POINT Output – 109
- Without Diagnostic Status 109
- With Over Load and Open 110
- Load Diagnostic Status 110
- With Over Load Diagnostic 111
- Digital 4 POINT Output – 112
- Analog 2 Channel Input 114
- INT 0 0…7,000 (0.00…70.00) 121
- Analog 2 Channel Output 123
- Specialty I/O 127
- Stored Data 131
- Program Fault 131
- Decimal Position 134
- Gate Interval 134
- Program Fault Note 136
- SSI Word Delay Time 138
- Sensor Resolution 138
- Sensor Cycle 138
- Compare 0,1 Value 138
- Present / Latched Data 139
- Quick Start 145
- Configure the Adapter 146
- Enter Adapter Properties 147
- 134 Quick Start 148
- Configure 1734 POINT I/O 149
- Modules 149
- 136 Quick Start 150
- IMPORTANT 151
- Configure an Ethernet 152
- Driver in RSLinx Software 152
- Quick Start 139 153
- 140 Quick Start 154
- 142 Index 156
- Rockwell Automation Support 158
- Documentation Feedback 158
Relacionado con productos y manuales para Redes Allen-Bradley Rockwell Automation 1734-AENT
(20 paginas)
Redes Allen-Bradley 1794-OE8H Especificaciones
(32 paginas)
(32 paginas)
Redes Allen-Bradley 1794-IE8H Manual de usuario
(146 paginas)
(146 paginas)
Redes Allen-Bradley 1794-IE8H Especificaciones
(136 paginas)
(136 paginas)
Redes Allen-Bradley 1738-ADNX Manual de usuario
(112 paginas)
(112 paginas)
Redes Allen-Bradley 1734-ADN Manual de usuario
(239 paginas)
(239 paginas)
Redes Allen-Bradley PLC-5 Manual de usuario
(2 paginas)
(2 paginas)
Redes Allen-Bradley 1784-KT/B Especificaciones
(67 paginas)
(67 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales