Allen-Bradley 2-D Manual de usuario Pagina 50
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-12 Parameters and Programming
57 [Program Lock]
When set to 1, all parameters will be protected against change by unauthorized
personnel.
0/1 Numeric
Value
0
58 [Internal Frequency]
When P59 - [Frequency Select] is set to a 1, this parameter will provide the drive
frequency command. This parameter will change the frequency command in “Real
time” using the up/down arrow keys. Maximum value is set in P33.
Important: Follow normal programming procedures. Once the desired
command frequency is reached, the Enter key must be pressed to
store this value to EEPROM memory. If the ESC key is used before
the Enter key, the frequency will return to the original value following
the normal accel/decel curve.
0.0/240.0 0.1 Hz 60.0 Hz
59 [Frequency Select]
Selects the source of the frequency command for the drive.
Settings: 0 = External frequency command from the Control Terminal Block (TB3)
1 = Internal frequency command from P58 - [Internal Frequency].
0/1
Numeric
Value
0
60 [Zero Offset]
Used to add or subtract any system offset to the analog input.
See P16 - [Analog Input] for additional information.
Important: This parameter cannot be programmed while the drive is running.
–50.0/+ 50.0 Numeric
Value
0%
[Preset Frequency 0-7]
The programmed value sets the frequency that the drive outputs when selected.
Refer to Chapter 2, Figure 2.21 for the Preset Speed model control wiring diagram.
0.0/240.0 0.1 Hz See Table
Program Group
No. Parameter Name/Description
Min./Max.
Range
Units
Factory
Default
Preset Speed Model Only
Signal Follower
Model Only
(Input Mode 8)
Preset Freq. Default
TB3-4
(SW3)
TB3-2
(SW2)
TB3-1
(SW1)
TB3-8
(SW2)
TB3-2
(SW1) Accel
➊
Decel
➊
61
Preset 0 3.0 HZ 0 0 0 0 0
P30
[Accel Time 1]
P31
[Decel Time 1]
62
Preset 1 20.0 Hz 0 0 1 0 1
63
Preset 2 30.0 Hz 0 1 0 N/A N/A
64
Preset 3 40.0 Hz 0 1 1 N/A N/A
65
Preset 4 45.0 Hz 1 0 0 1 0
P69
[Accel Time 2]
P70
[Decel Time 2]
66
Preset 5 50.0 Hz 1 0 1 1 1
67
Preset 6 55.0 Hz 1 1 0 N/A N/A
68
Preset 7 60.0 Hz 1 1 1 N/A N/A
➊
When using P46 - [Input Mode] setting 4, the Accel and Decel times are selected by providing an input to TB3-8.
See Chapter 2, Figure 2.12 for additional information.
This parameter applies only to the Analog Signal Follower model.
This parameter applies only to the Preset Speed model.
- 160 SSC™ 1
- Variable Speed 1
- (Series C) 1
- Important User Information 2
- Series C Summary of Changes 3
- Table of Contents 5
- Getting Started 7
- 160 -AA02 N SF1 P1 8
- 160-AA02NSF1P1 9
- Standard Drive Features 10
- Optional Drive Features 11
- End of Chapter 12
- Installation and Wiring 13
- Power Wiring 14
- Specifications 15
- Terminal Block Wiring 15
- Motor Branch Circuit Analysis 16
- Input Power Conditioning 18
- Motor Cable Types 18
- Reflected Wave Protection 19
- Capacitive Current Coupling 20
- Nm (lb in) 21
- Wiring Diagram Key 22
- 2-12 Installation and Wiring 24
- Installation and Wiring 2-17 29
- Analog Frequency Sources 30
- Preset Frequency Sources 31
- Internal Frequency Source 32
- Program Keypad Module 33
- Key Functions 34
- Program Keypad Module 3-3 35
- Installation 36
- Start-Up 37
- 4-2 Start-Up 38
- Parameters and Programming 39
- Important Reset Actions 40
- Programming Example 40
- Display Group (Read Only) 43
- 0/48 Numeric Value 43
- Program Group Parameters 44
- % [Base Frequency] 45
- % [Base Voltage] 45
- 46 [Input Mode] 47
- 47 [Output Configure] 47
- 48 [Output Threshold] 47
- 49 [PWM Frequency] 48
- 50 [Restart Tries] 48
- 51 [Restart Time] 48
- 52 [DB Enable] 48
- 53 [S-Curve] 49
- 54 [Clear Fault] 49
- 55 [Memory Probe Address] 49
- 56 [Reset Functions] 49
- Preset Speed Model Only 50
- Signal Follower 50
- Model Only 50
- Settings: 52
- 81 [PI Proportional Gain] 53
- 82 [PI Integral Gain] 53
- 83 [PI Process Reference] 53
- 84 [PI Dead Band] 53
- 160 PI Control Setup 54
- Troubleshooting 57
- Problem Corrective Action 59
- 6-4 Troubleshooting 60
- CSA 22.2 62
- Specifications A-3 63
- End of Appendix 64
- Accessories and Dimensions 65
- Accessory Dimensions 66
- Line Filters Figure B.3 67
- MADE IN U.S.A 68
- 29 ➊ 69
- Drive Dimensions 70
- 5.5 (0.22) 72
- Mounting Holes—2 Places 72
- CE Conformity 75
- Shielded Enclosure 76
- Cable Clamps 77
- Motor Cable 77
- Control Wiring TB3 78
- Ground Terminal – PE 78
- CE Conformity C-5 79
- Index-10 90
Relacionado con productos y manuales para Lectores De Códigos De Barras Allen-Bradley 2-D
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales